E-TECH Heavy Duty Body and Bumper Guard Kit - 47mm Wide
Price:
Availability:
The E-TECH Heavy Duty Body and Bumper Guard fits along the side of your vehicle or to the bumpers and is designed to act as a buffer to prevent damage to the body paintwork.
The knocks, dents and chips that your vulnerable body and paintwork can acquire in a car park from other cars or from opening the door onto a pillar or post can be prevented.
E-TECH Body and Bumper Guard is self adhesive and uses high quality automotive adhesive tape which is applied to a primer that will guarantee a secure adhesion.
The E-TECH Body and Bumper Guard is supplied in a 5 metre roll, with 8 injection moulded end caps, enough to cover most cars, and it is simple to fit.
Body and Bumper guard can be fitted to any painted metal panel in any position and also to most bumpers.
Features:
- Protects paint and bodywork from knocks, bumps and scratches for all round protection
- Designed to fit bodywork and painted bumpers
- Helps maintain your vehicle's re-sale value
- The sost P.V.C material will conform to the shape of most bumpers & bodywork
- Can be fited to any painted panel in any position - Easy to fit
E-TECH Body and Bumper Guard Dimensions: 47mm wide x 6mm deep
Colour: Black
Roll Length: 5 metres
3M Adhesive tape pre bonded to the entire roll
8 x self-adhesive end caps supplied along with 2 x E-TECH Cleaning Sachets
NOT SUITABLE FOR A.B.S/PLASTIC/POLYPROPYLENE BUMPERS WHICH HAVE A TEXTURED OR ROUGH SURFACE
IMPORTANT:
READ THE INSTRUCTIONS BELOW BEFORE FITTING THE BODY AND BUMPER GUARD
Contents of Kit:
1 x 5 metre roll of E-TECH Body and Bumper Guard Moulding
8 x E-TECH Injection Moulded End Caps
2 x E-TECH 'Surface Cleaner' Sachets
Thoroughly clean the area along the side of the vehicle where the Body and Bumper Guard is going to be fitted.
IMPORTANT
This area must be completely free of all traces of all oil, grease, wax polish, dirt, dust and moisture. Thoroughly dry the area.
Do not fit in temperatures below 55ºF (13ºC) as this affects the adhesion of the product. If the temperature is below 55ºF (13ºC) you can warm the Body and Bumper Guard up and the area where it is going to be stuck using a hair dryer or by fitting it in a warm garage.
Using the 'E-TECH Surface Cleaner' sachet provided, wipe around the area where the Body and Bumper Guard is going to be fitted. The 'Surface Cleaner' sachet will prepare the bonding area for the Body and Bumper Guard so strong adhesion is achieved.
When fitting the Body and Bumper Guard to the side or the bumpers of the vehicle, it is a good idea to stick some masking tape along the side of the vehicle to act as a guide. Stick the Body and Bumper Guard above or below the masking tape and use it as a reference so you stick the Body and Bumper Guard on straight.
When you have decided where you want to fit the Body and Bumper Guard, unroll it and measure the lengths needed. Cut the Body and Bumper Guard to the required lengths using a sharp knife or pruning shears.
Remember to allow approx. 5-10mm gap from door shut edge – see fig. 1. Ensure that the Body and Bumper Guard does not foul the door opening and closing.
Offer up the cut lengths of Body and Bumper Guard – make sure you have them in the correct position, peel back only 5 or 6 cms of the backing paper and fold this down to leave a flap. Do not touch the adhesive tape or the bonding area with your fingers.
Stick the exposed end of the Body and Bumper Guard in position and rub down gently. Then pull the flap of the backing paper away from the Body and Bumper Guard a few cms at a time and slowly stick the rest of it in position, rubbing down gently as you go. Once the moulding is in place it should not be removed. Repeat the process for all the lengths.
DO NOT STRETCH THE BODY AND BUMPER GUARD WHILE INSTALLING
Now with the moulding in position stick the injection moulded end caps over the ends of the moulding for a professional finish.